Most owners assume any replacement part labeled for wet-dry floor cleaners will snap right into their automated unit. In reality, ordering accessories meant for upright stick cleaners or slightly different robot lines almost always leads to cracked wet tanks and ruined wood floors. A tank that lacks a watertight seal drips dirty puddles across floorboards while the machine sits idle, while an incompatible battery pack causes the motor to cut out after only five minutes. Dealing with a stalled robot usually comes down to small hardware mismatches that waste both weekend hours and hard-earned cash.
Restoring quiet, hands-free mopping only requires verifying a few critical connection points before ordering. Confirm that the wet tank bracket specifically lists model 28599, ensure any fresh power cell matches the required 14.4-volt connector, and check that the side brushes snap on without forcing the motor spindles. Once the proper pieces click into place, hard surfaces get cleaned thoroughly without unwanted puddles or mid-cycle shutdowns. The options below detail exact-fit replacement components that return your wet-dry robotic vacuum to peak cleaning performance throughout 2026.
Brand new,Wet Tank & Pads For Bissell SpinWave Wet & Dry Robotic Vacuum part number, 1624766.Suitable for BISSELL SpinWave Wet and Dry Robotic Vacuum, Series 2859, 3115.Fits Models:28599, 3115, 28597, 2859W, 2859T, 28596
Key specs
- Replacement Part Fit
- Matches part number 1624766 to restore wet mopping mode on Bissell SpinWave robotic models 28599 and 3115 without replacing the entire robotic cleaner.
- Supported Robot Series
- SpinWave 28599 and 3115
- SpinWave 28597 and 2859W
- SpinWave 2859T and 28596
Pros:
- Explicitly matches Bissell SpinWave series 2859 and 3115
- Direct replacement for factory part number 1624766
- Supplied as an assembled wet tank module with pads
- Fits models 28599, 3115, 28597, 2859W, 2859T, and 28596
Cons:
- Only replaces the wet tank assembly, not the dry dust bin
- Listing measurements list 2 x 1 x 3 inches, so verify slot fit before install
⚡The component of this product is 1624766 Wet Tank & Pads, which is used with the Dust collector and is a separate part.⚡Condition ：New: A brand-new, unused, unopened, undamaged item in its original packaging.⚡Fits Models: 28599, 3115, 28597, 2859W, 2859T, 28596⚡1624766 Wet Tank & Pads 10*4*4 inches
Key specs
- Casing Dimensions
- 10 x 4 x 4 inches
- Tank Installation Notes
- Operates as a separate fluid reservoir module that slots in place of the standard dry dust container on compatible 2859 and 3115 series robotic vacuums.
Pros:
- Clear tank housing lets you view remaining fluid levels directly
- Listed with precise 10 x 4 x 4 inch outer casing dimensions
- Separates liquid mopping functions from the dry dust collector
- Directly replaces worn part 1624766 across 2859 series units
Cons:
- Unbranded generic component rather than Bissell original factory equipment
- Pad thickness and exact pad counts are unstated in the listing
REPLACEMENT EDGE BRUSHES: Designed to fit Bissell SpinWave Wet & Dry Robotic Vacuum, for bissell Edge Brushes replace accessories 2859J, 28599, 3115, 28597,2859W,2859T, 28596,2859Z.Just remove the old brush and snap on the new one, no tools required.Made of high quality material, durable and long la
Key specs
- Brush Roll Attachment
- Engineered for snap-on mounting into the existing edge motor sockets without using screwdrivers or prying tools.
- Edge Sweeper Pack
- 2 snap-on replacement brushes
Pros:
- Tool-free snap-on design allows quick edge brush replacement
- Includes 2 edge brushes to refresh both spinning sweepers at once
- Works on hard surfaces and carpets to sweep debris into the path
- Broad model support including 2859J, 28599, 3115, and 2859Z
Cons:
- Ultra-lightweight 0.02 lb plastic hub requires care when unsnapping
- Does not include the central rotating brush roll or mounting screws
Battery Specification: Capacity: 2600mAh Voltage: 14.4V.100% brand new. High-quality materials and circuit board.Replacement For Models: Fit for Bissell 2859 3115 28596 28597 2859T 2859W SpinWave Wet and Dry Robotic Vacuum.Compatible with Part Number: Fit for 5345 1618526 1625424 Z65B155.Safety Abov
Key specs
- Battery Specifications
- Voltage: 14.4V
- Capacity: 2600mAh
- Part match: 1625424, 1618526, 5345, Z65B155
- Safety marks: CE, FCC, RoHS
- Warranty and Support
- 12-month exchange guarantee
Pros:
- 2600mAh capacity matches original runtime requirements
- 14.4V rating matches factory specification for 1625424 batteries
- Certified by CE, FCC, and RoHS with built-in short circuit protection
- Backed by a 12-month exchange guarantee from the manufacturer
Cons:
- Requires unscrewing the base plate for internal battery compartment access
- Rated 14.4V rather than the 14.8V seen on select alternate battery packs
【Part Number】Vacuum Cleaner Wet Tank and Pads Part Number 1624766【Fits the following models (not all applicable models may be listed)】28599, 3115, 28597, 2859W, 2859T, 28596【Design】Made of high-quality materials, it can keep you vacuum cleaner safe and in working condition all the time, durable, con
Key specs
- Tank Shell Fit
- Built to factory 10 x 4 x 4 inch specifications to fit cleanly into the wet-mode receptacle on 2859 and 3115 chassis.
Pros:
- Full replacement module for damaged or leaking 1624766 wet tanks
- Clear plastic tank structure matches OEM 10 x 4 x 4 inch dimensions
- Designed for tool-free disassembly and straightforward installation
- Restores mopping capability to Bissell 28599, 3115, and 2859W units
Cons:
- Third-party replacement part without stated manufacturer warranty period
- Fabric pad composition and care instructions are omitted
EVERY PURCHASE SAVES PETS. BISSELL proudly supports BISSELL Pet Foundation and its mission to help save homeless pets.VACUUM AND WASH AT THE SAME TIME. Makes everyday pet mess cleaning quick and easy.MULTI-SURFACE CLEANING. Safe and effective for use on tile, sealed wood floors, laminate, linoleum,
Key specs
- Floor Types Supported
- Engineered for multi-surface cleaning across tile, sealed wood, laminate, vinyl, linoleum, and low-pile area rugs.
- Cleaner Form Factor
- Type: Corded upright wet-dry vac
- Weight: 11 lb
- Tanks: Clean and dirty water separation
- Coverage: Hard floors and area rugs
Pros:
- Simultaneously vacuums dry debris and washes hard floors and rugs
- Dual-tank system keeps fresh solution separate from dirty tank recovery
- Tangle-free brush roll and pet hair guard prevent internal clogging
- Backed by a 3-year limited warranty from Bissell
Cons:
- Manual upright floor cleaner weighing 11 lb instead of an automated robot
- Corded operation requires standard wall outlet power rather than battery
EVERY PURCHASE SAVES PETS. BISSELL proudly supports BISSELL Pet Foundation and its mission to help save homeless pets.VACUUM and WASH AT THE SAME TIME. BISSELL CrossWave multi-surface floor cleaner cleans better than a sponge mop and bucket, and in less time.2MULTI-SURFACE CLEANING. Safe and effecti
Key specs
- Cleaner Operation
- Functions as a dedicated upright wet-dry vacuum and mop combo, offering heavy manual stain removal compared to robotic maintenance mopping.
Pros:
- Full upright wet and dry floor washer designed for stubborn floor messes
- Washes sealed bare floors while lifting dirty water in a single run
- Suitable alternative when robotic mopping lacks scrubbing capacity
- Genuine Bissell manufactured unit with full factory construction
Cons:
- Requires manual pushing and storage space for a full upright machine
- Detailed specifications like tank capacity and cord length must be verified
Compatible Part Numbers: SpinWave Wet Dry Robotic Vacuum 2859, 3115Original Part Numbers: Bissell 1625424Volts: 14.8Volts / Type: Li-ionCapacity: 2600mAh100% Compatible with original battery
Key specs
- Battery Cell Rating
- 14.8V Li-ion, 2600mAh
- Component Weight
- 0.42 lb pack weight
Pros:
- 14.8V Li-ion pack matches higher-voltage factory replacements
- 2600mAh capacity provides standard robotic operational runtime
- Compact 0.42 lb battery drops into the factory internal slot
- Direct replacement for Bissell OEM part number 1625424
Cons:
- Warranty is listed as non-applicable by the seller
- Restricted to SpinWave 2859 and 3115 models without universal connector fit
Every Purchase Saves Pets. BISSELL proudly supports BISSELL Pet Foundation and its mission to help save homeless pets..Runtime : 130 minutesTwo Tank Cleaning System. Powerfully vacuum or actively mop your floors.Lithium Ion Battery. Provides up to 130 minutes of run time on hard floors in low mode a
Key specs
- Run Time per Charge
- Up to 130 minutes in low mode
- Suction Power
- Up to 1500 Pa in dry vacuum mode
- System Navigation
- Integrates WiFi connectivity with structured navigation patterns to clean hard surfaces systematically before returning to dock.
Pros:
- Up to 130 minutes of run time on hard floors via lithium-ion battery
- Triple Action Cleaning System delivers up to 1500 Pa dry suction
- Two-tank system switches between dry vacuuming and active wet mopping
- WiFi-connected with structured navigation for systematic floor passes
Cons:
- Recharge cycle requires 4 to 5 hours on the docking station
- At 3.25 inches tall, verify clearance under low-slung cabinets and sofas
Last update on 2026-09-29 / Affiliate links / Images, Product Titles, and Product Highlights from Amazon Product Advertising API
Will part number 1624766 fit the Bissell SpinWave 28599 wet tank slot properly?
Yes, part number 1624766 is the exact replacement wet tank and pad assembly built to fit model 28599. It operates as a separate component used alongside the dust collector to switch your machine into active mopping mode. Listings show compatibility across the robotic series, fitting models 28599, 3115, 28597, 2859W, 2859T, and 28596. Choosing this specific part number prevents leaks across sealed hard floors caused by ill-fitting aftermarket reservoirs.
Which replacement battery matches the voltage and connector of model 28599?
Replacement packs under original part number 1625424 supply the direct physical and electrical match for the 28599 robotic vacuum. Compatible listings provide a 2600mAh capacity rated at either 14.4V or 14.8V, designed to slide directly into the battery compartment. This matches the factory specifications of the 2859 robotic family, including models 3115, 28596, and 2859W. Verifying the 1625424 part number ensures your unit receives proper charging current on the dock without mid-cycle shutdowns.
How do you replace the edge brushes without damaging the motor assembly?
Replacement edge brushes, identified by part number 1624772, snap directly onto the underside drive posts without tools. To remove a worn blue-black corner brush, pull firmly upward from the base of the bristles to pop it off the motor spindle. Align the new brush over the keyed post and press down until it clicks securely into place. This snap-on design protects the internal drive gears while restoring edge-cleaning reach along baseboards on models 28599, 3115, 28597, and 2859Z.
Can parts for upright CrossWave machines be used on the SpinWave 28599 robot?
No, upright CrossWave components cannot be installed on SpinWave robotic vacuums. Upright models like the CrossWave Pet Pro 2306A measure 46 inches tall, weigh 11 pounds, and use wide roller assemblies designed for upright floor cleaning. The SpinWave 28599 uses distinct modular accessories, such as snap-on edge bristles and the dedicated 1624766 mopping module. CrossWave brush rolls, filters, and tanks will not physically mount to a low-profile robotic chassis.
How do I know if an accessory fits both the 28599 and other SpinWave models?
Check the compatibility list for shared chassis numbers, specifically models 3115, 28597, 2859W, and 28596. The 1624766 clear wet tank and the 1624772 dual-pack edge brushes work across these specific 2859-series variants. Newer models like the WiFi-connected 3347 offer a listed runtime of 130 minutes and share the two-tank cleaning format, but accessory dimensions can vary. Always confirm that 28599 appears in the supported model list before replacing tanks or brackets.
Is it better to repair a model 28599 or switch to a full-sized wet-dry vacuum?
Replacing the modular battery or tank restores automated daily hard-floor maintenance on a working robot for minimal expense. But if your living space includes thick carpeting or heavy spills, an upright machine like the CrossWave 2306A vacuums wet and dry debris simultaneously with a tangle-free brush roll. For homes needing manual wand control to manage bare floors alongside delicate surfaces, exploring a Bissell hard floor vacuum can provide steady suction without relying on robotic navigation routines.
